Differenze
Queste sono le differenze tra la revisione selezionata e la versione attuale della pagina.
| Prossima revisione | Revisione precedente | ||
|
projects:domus [16/11/2015 13:07] alez created |
projects:domus [26/11/2017 21:37] (versione attuale) alez [User Interfaces] |
||
|---|---|---|---|
| Linea 24: | Linea 24: | ||
| * communicating with the attached peripherals; | * communicating with the attached peripherals; | ||
| * gain autonomy (respond to inputs switching outputs etc); | * gain autonomy (respond to inputs switching outputs etc); | ||
| - | * working as gateway to the Ethernet. | + | * working as gateway to the Ethernet; |
| + | * be configurable in stand-alone (web interface) but when connected to a network should be ideally configurable automatically by the system (just configure the "master" device, all peripheral intelligent units will be automatically configured for stand-alone autonomy operation). | ||
| * some user interfaces (touch panels), communicating over ethernet, running specific software | * some user interfaces (touch panels), communicating over ethernet, running specific software | ||
| * PSU | * PSU | ||
| + | |||
| + | {{:projects:domus.png?direct&300|}} | ||
| ==== State of art ==== | ==== State of art ==== | ||
| - | Developing peripherals. Nothing ready. | + | Input/output peripherals ready. |
| + | |||
| + | Temperature sensor still under development. | ||
| + | |||
| + | Now working on the CPU unit. | ||
| ===== Peripherals ===== | ===== Peripherals ===== | ||
| Linea 37: | Linea 44: | ||
| {{:projects:img-20151017-wa0002.jpg?300px|}} | {{:projects:img-20151017-wa0002.jpg?300px|}} | ||
| + | First prototype boards: | ||
| + | |||
| + | (16 input board, 8 relay output board, temperature sensor board) | ||
| + | |||
| + | {{:projects:img_20151231_190104607.jpg?400|}}{{:projects:prod1.jpg?400|}} | ||
| ==== DIN - 16 dig. input module ==== | ==== DIN - 16 dig. input module ==== | ||
| + | |||
| + | Article Code: **MAEDI16D** | ||
| + | |||
| + | This module features 16 opto-isolated inputs and modbus communication. | ||
| + | |||
| + | First batch produced! | ||
| + | |||
| + | {{:projects:domus:maedi16d.jpg?400|}} | ||
| + | |||
| + | |||
| + | Full features: | ||
| + | |||
| + | * 16 opto-isolated inputs active connecting the input to ground: easy installation; | ||
| + | * Input mild filtering; | ||
| + | * Three readable registers, one (0) for instantaneous status, one (1) for the previous status (reset after reading), one (2) for the previous status (reset after writing something to the same register). | ||
| + | * Input leds that indicate status of inputs, they can be enabled and disabled through pushbutton or permanently with dip-switch; | ||
| + | * Data led, indicates whenever a modbus function is accomplished; | ||
| + | * Error led, indicates whenever a modbus function cannot be satisfied; | ||
| + | * Peripheral reset button; | ||
| + | * 12VDC power supply. | ||
| ==== DIN - 8 relay output module ==== | ==== DIN - 8 relay output module ==== | ||
| + | |||
| + | Article Code: **MAEDR8D** | ||
| + | |||
| + | Module featuring 8 relay normally open outputs for power loads. | ||
| + | |||
| + | First batch produced! | ||
| + | |||
| + | {{:projects:domus:maedr8d.jpg?400|}} | ||
| + | |||
| + | Features: | ||
| + | * 8 relay NO outputs; | ||
| + | * uses OMRON G5Q relais, 250VAC 10A resistive load; | ||
| + | * One modbus register readable and writable; | ||
| + | * Front panel leds indicate status of outputs; | ||
| + | * Front panel leds can be enabled or disabled with a toggling pushbutton or a dip switch; | ||
| + | * Data led: flashes whenever modbus request has been accomplished; | ||
| + | * Error led: flashes whenever modbus request cannot be satisfied; | ||
| + | * Front panel reset button; | ||
| + | * 12VDC power supply. | ||
| ==== Temperature sensor ==== | ==== Temperature sensor ==== | ||
| + | |||
| + | Article code: **MAEDTSP** | ||
| + | |||
| + | Ambient temperature sensor, fits inside one modular wall device (Vimar Plana), Modbus communication. | ||
| + | |||
| + | Under development. | ||
| + | |||
| + | {{:projects:domus:maed2011.jpg?300|}} | ||
| ===== Intelligent Units ===== | ===== Intelligent Units ===== | ||
| + | Call them CPU modules, Central units or intelligent units, this is a core for the system. It can work independently or as a peripheral unit in a LAN network. | ||
| + | |||
| + | Features ARM CPU, Modbus master line(s), LAN connection. | ||
| + | |||
| + | Under development. First PCB prototypes: | ||
| + | |||
| + | {{:projects:domus:img_20151221_203250815.jpg?200|}} | ||
| + | {{:projects:domus:15178984_1265235023533435_4288828194913795156_n.jpg?200|}} | ||
| + | {{:projects:domus:15095051_1265235030200101_7986378943087001829_n.jpg?200|}} | ||
| ===== User Interfaces ===== | ===== User Interfaces ===== | ||
| + | User Graphical interfaces, with a touch screen display for interaction with the system. | ||
| + | |||
| + | Under development. | ||
| + | |||
| + | |||
| + | Some photo of first hardware prototype. | ||
| + | |||
| + | |||
| + | {{:projects:domus:maed4011.jpg?500|}} | ||
| ===== PSU ===== | ===== PSU ===== | ||
| It is possible to have a PSU for each peripheral, or centralize them. | It is possible to have a PSU for each peripheral, or centralize them. | ||
| Centralizing them can be convenient bacause you can use only one 12V lead acid battery as backup power for the whole system (except for additional networking infrastructures, such as ethernet switches). | Centralizing them can be convenient bacause you can use only one 12V lead acid battery as backup power for the whole system (except for additional networking infrastructures, such as ethernet switches). | ||
| + | |||
| + | |||
| + | ====== Related links ====== | ||
| + | |||
| + | * https://github.com/souliss/souliss/wiki | ||
| + | * https://github.com/openhab/openhab1-addons | ||
| + | * https://www.crowdsupply.com/patternagents-llc/thingsoc-grovey | ||
